斜顶模具英文

不知道你想问那种模具？塑料？冲压？都来一点算了：CAD/CAM: Computer –aided Design and Computer –aided ManufacturingNC : Numerical ControlCNC: Computer Numerical ControlEDM: Eletrodischarge Machining （ 电火花加工 ）copy milling 仿形铣die block 模块electrode 电极hobbing 反印制模法 electrochemical machining 电化学加工parting (line) plane 分模面 draft 拔模斜度corner( fillet) radius 外（内）圆角半径 web 筋 rib 肋 punchout 连皮knock-out pins 顶杆thermal fatigue 热疲劳die wear 模具磨损 heat checking 热龟裂 steep temperature gradient 温度梯度高blanking punchingnotching perforatingtrimming shavingslitting lancingforming flanges embossingcurling squeezingbulging coiningupsetting extruding 不想写下去了，好像我只写了一点点皮毛。

项目香港术语国内术语英语1法兰定位圈Locating ring / Resister ring2唧嘴注道衬套 / 注口衬套Sprue bushing 3面板 / 码模板前固定板Front clamping plate / Front plate4边导柱 / 合模销 / 导销Guide piller / Leader pin5Ａ板 / 模板型腔固定板Front cavity plate / 'A' plate / Cavity plate6模 / 内模型腔 / 模腔 / 阴模 / 模穴 / 母模Cavity7�7�3 / 内模型芯 / 模腔 / 阳模 / 模穴 / 公模Core8Ｂ板 / �7�3板 型芯固定板Rear cavity plate / 'B' plate / Core plate9司导套 / 合模销衬套Guide bush / Leader pin bushing10托板托板 / 支撑板Support plate11凳仔方垫块 / 隔条Spacer block12弹弓弹簧Spring13顶针面板顶杆固定板 / 脱模销托板Ejector retainer plate14勾针拉料杆 / 注口冷料脱模销Sprue puller15顶针顶杆 / 脱模销Knock out pin / Ejector pin16回针 / 扶针复位杆 / 回位销Return pin17顶针底板顶杆托板 / 脱模销座板Ejector plate18撑头 / 模顶支承柱 / 支模柱Supporting pillar19垃圾钉限位钉Stop pin20底板後固定板Rear clamping plate / Back plate

一、入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round (full/half runner) 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴：hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板：support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock 顶针：ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate 缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）： mold base 上内模：cavity insert 下内模：core insert 行位（滑块）： slide 镶件：insert 压座/斜鸡：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴： sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug 锁模块：lock plate 斜顶：angle from pin 斜顶杆：angle ejector rod 尼龙拉勾：parting locks 活动臂：lever arm 复位键、提前回杆：early return bar 气阀：valves 斜导边：angle pin 术语：terms 承压平面平衡：parting surface support balance 模排气：parting line venting 回针碰料位：return pin and cavity interference 模总高超出啤机规格：mold base shut hight 顶针碰运水：water line interferes withejector pin 料位出上/下模：part from cavith (core) side 模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件： Do not use (core/cavity) insert 用铍铜做镶件： use beryllium copper insert 初步（正式）模图设计：preliinary (final) mold design 反呵：reverse core 弹弓压缩量：spring compressed length 稳定性好：good stability,stable 强度不够：insufficient rigidity 均匀冷却：even cooling 扣模：sticking 热膨胀：thero expansion 公差：tolorance 铜公(电极)：copper electrode