模具推板英文

不知道你想问那种模具？塑料？冲压？都来一点算了：CAD/CAM: Computer –aided Design and Computer –aided ManufacturingNC : Numerical ControlCNC: Computer Numerical ControlEDM: Eletrodischarge Machining （ 电火花加工 ）copy milling 仿形铣die block 模块electrode 电极hobbing 反印制模法 electrochemical machining 电化学加工parting (line) plane 分模面 draft 拔模斜度corner( fillet) radius 外（内）圆角半径 web 筋 rib 肋 punchout 连皮knock-out pins 顶杆thermal fatigue 热疲劳die wear 模具磨损 heat checking 热龟裂 steep temperature gradient 温度梯度高blanking punchingnotching perforatingtrimming shavingslitting lancingforming flanges embossingcurling squeezingbulging coiningupsetting extruding 不想写下去了，好像我只写了一点点皮毛。

snap joint 例句：It mainly introduces a new joint technology of self—tapping screw, insert joint after injection molding, snap joint, etc. 重点介绍了自攻螺钉连接、模塑后嵌入的嵌件连接,卡入连接等较新的连接技术。 Typical mechanical functions such as threaded fastener, snap joint and plug-in terminals can be integrated into an interconnected device. 能够集成的典型机械功能包括螺纹紧固、搭扣连接、插头连接等。

gate type: pin point gate.通常译为浇口，而非“胶”口。浇口类型通常分为侧浇口(side gate)，潜浇te(sub gate)，点浇口(pin point gate)，扇形浇口(fan gate)等等。

一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口： pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座： connector socket密封/封料： seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝： screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring

snap joint