王豆豆228
The installation, use:1 correctly connected to the power supply, before the start, first hand pull the inertial wheel, check whether there is abnormal debris in machine room.2 boot idle check cutter turning right or not, such as the emergence of direction reversal, please change the three-phase power line wiring sequence; determine the cutter turning right after the start, idle operation 10 minutes, fastening send feeding chamber, so that the protection switch contacts completely, with broken condition, can feed production.3 prohibited into iron and other hard objects into the crushing chamber.4 found abnormal sound Renqing production downtime, checking the occurrence reasons, troubleshooting before reboot.5suggestions to mechanical installation work in a separate place.Maintenance, maintenance instructions:1should be the starting motor in mechanical ventilation position, ensure the motor heat dissipation, prolong the service life of motor.2regular inspection tool bolt, the new machine using a week later, use special tool to the knife blade and the blade holder bolt, strengthen the fixed.3ball rolling bearings: every 20 days to ensure the bearing mouth filling grease, rolling bearing between the sob sinking.4to ensure the tool notch sharpness, according to the use condition, regularly check the knife blade, ensure sharpness, reduced by the blade blunt day missing and caused unnecessary damage to other components.5second times before the start, should first remove the engine room the first material breaking when the remaining scrap, reducing the starting resistance, reducing the starting load of the motor, should be regularly opened the inertial wheel and the belt wheel cover, removing flange beneath the ash outlet, solid machine chamber surplus scrap into the rotating bearing.6time of tool change, keep moving knife and the fixed knife incision between clearance: with0.5- 0.8mm to prepare, recycling materials thinner, smaller incision gap can be recycled; the thicker, incision gap should be appropriately amplified.7 regularly check whether the belt is loose, if the belt relaxation, loosen the motor fixing bolt, with special tool motor outward mobility, until the belt tensioner.Welcome to use the company's products, the company will be happy for your service.In order to give you a correct, efficient use of this product, please read this manual carefully before use.Applies to the motor power below 20HP crusher (with magnetic starting switch )Start wiring diagramApplies to the motor power is higher than 20HP crusher
摄氏三十八度
Ask ace to help you! Thank you! In reply E-mail today! Installation, use instructions: 1 the correct connected to the power source, and before the start, with the hand first move round out the inertia, check the machine indoor are normal sundry exist. 2 boot idling check cutting knife to correctly, such as a reverse direction, please exchange three-phase power connection order; Determine the cutting knife to correct, the start ticking over 10 minutes, fasten send feed room, make protection switch completely contact, accord with broken conditions, can feed production. 3 in iron and other good thing ban into broken material room. 4 found that when that igawa abnormal sound in stop and check the cause and remove the faults rear can restart. Five Suggestions to mechanical installation in independent work place. The maintenance, the maintenance explains: 1 should put machinery start motor position in ventilation, ensure motor work quantity of heat to send out, to extend the life of motor. 2 regular inspection tools bolt, the brand new machine use after a week, with a special tool to sword bolt, strengthen the blade and tool of the immobility of between. 3 insert rolling bearing: every 20 days to bearing mouth should be filling butter, ensure the rolling bearing the cry sink between sex. 4 to ensure tools incision sharpness, based on the using condition, regular inspection sword, guarantee the sword sharpness, reduce the day of blade caused by blunt rest parts of the damage is not necessary. 5 second start before, should try to clear machine room the first time when the material to the rest of the broken material, reducing starting resistance, reduce motor start load, should be regularly apart inertia wheel cover and pulley cover, clear the flange constructed below the ash, solid machine room eduction JiYu broken material into the rotation bearing. 6 change tool, keep moving knife and the fixed knife of incision between gap: to 0.5-0.8 mm for preparation, recycling the thin material, can be the appropriate clearance incision small; Recycling material is thicker, incision clearance shall be properly amplification. 7 regularly check whether belt flabby, if appear belt flabby, should loosen the retaining bolt motor, with a special tool to mobilize the motor outside, until the belt taut so far Welcome to use our products, our company will sincerely service for you. You are correct, quickly use this product, please you before use carefully read the instruction. Apply to the motor power of 20 HP the following crusher (with electromagnetic starter switch system) Start wiring diagram Apply to the motor power more than 20 HP's crusher
优质英语培训问答知识库
