重新标定英文翻译

n. 圆规(纸的厚度)vt 用卡规测量caliper.. 1. 卡尺4、卡尺（Caliper）和TapeMeasure测量长距离不同，Caliper测量的是短距离。在屏幕上有两个和实img.myitcar.com- 基于166个网页 2. 制动钳汽车行业--汽车专业中英文对照(C) ...Calibration 校正；标定 Caliper 卡钳，卡尺，圆规；制动钳 Caliper disc brake 钳盘式制动器 ...3. 卡钳，卡尺，圆规汽车行业--汽车专业中英文对照(C) ...Calibration 校正；标定 Caliper 卡钳，卡尺，圆规；制动钳 Caliper disc brake 钳盘式制动器 ...4. 井径仪地质专业英语词汇(C-D) ...californium 锎caliper 井径仪caliper logging 井径测量 ...

caliper ['kæləpɚ] ['kælɪpə] 1. 名词 [通常用复数形态]卡钳，卡规；两脚规，圆规；测径器 inside calipers 内卡钳 outside calipers 外卡钳 2. 名词 【同义词】caliper rule 3. 名词 纸（或卡纸）的厚度 4. 名词 碟形制动器；碟掣 5. 及物动词 用测径器（或卡规）测量 6. 不及物动词 用测径器（或卡规）测量 PSI英文全称为Pounds per square inch。P是磅pound，S是平方square，I是英寸inch。把所有的单位换成公制单位就可以算出：1bar≈14.5psi 好像是测量的手法，用8磅/平方英寸的力度的卡钳测出来的结果。但愿有帮助。

caliper n. 测径器,卡钳,弯脚器 vt. 用卡钳测量 是不是应该问问懂化学的人啊？

大概就是这样了，不过会有误差请谅解3 then duly 220VAC and 24VDC main power and backup power supply, switch mode of choice for the "automatic", open the control counter-board power switch, control board counter the "main power" and "standby power" light is lit, "automatic sampling" light is lit, the system automatically run the first warm-up mode (the length of time for 0-1 minutes, can be observed on the screen Guangzhu progress), after the completion of warm-up into the automatic purge mode, use after decompression 4KG/CM2 the highest clean air for all testing conducted scavenging accommodation in order to rule out the possibility of sampling the water and gas pipelines and other objects, all detected light work of accommodation shown as "Scavenging"; Purge work is completed, sampling pumps work automatically to regulate the flow meter instructions to 1 L / MIN, the system automatically switches through the electromagnetic valve sampling space, the corresponding indicator light detection work space shown as "sampling", the screen shows the current measuring point of the combustible gas concentration readings ( Each detection channel switching time sampling length of 1-999 seconds, can be adjusted on the screen menu, the channel sampling the length of time can be individually set to a long time can also be unified settings). At this point the system has entered a state of normal operation. 4.4 Press the control panel counter test button, all lights and the panel should work buzzer. 4.5 If a class of combustible gas detection concentration above 10% LEL alarm default pre-concentration (0-50% LEL, can adjust the menu screen), pre-alarm status indicator light flashes (low frequency), buzzer-ming ring (low frequency), press the mute button, buzzer stopped ringing, pre-alarm status indicators into Always; if other detection accommodation exceeded again, the sound and light warning will come up again; If all the combustible gas detection accommodation concentration of less than default, press the reset button, pre-alarm status indicator goes out. Pre-alarm space, time, concentration of historical records and other information can display the relevant page inquiries, show. When the pre-alarm state, please stop hot work industry, check the relevant class of combustible gas leakage, and to exclude. 4.6 If a class of combustible gas detection concentration above 30% LEL alarm default main concentration (0-50% LEL, can adjust the menu screen), the main alarm status indicator light flashes (HF), buzzer ringing (high frequency), press the mute button, the buzzer to stop ringing, the main alarm status indicators into Always; if other detection accommodation exceeded again, the sound and light warning will come up again; If all the testing space combustible gas concentrations below the default, press the reset button, indicator light to turn off the main report to the police state. Alarm Master of accommodation, time, concentration of historical records and other information can display the relevant page inquiries, show. When the main report to the police state, please stop hot work industry, check the relevant class of combustible gas leakage, and to exclude. 4.7 Internal control cabinet combustible gas concentration monitoring by separate combustible gas sensor is responsible for continuous monitoring at any time, if the concentration of combustible gases inside the instructions more than 30% LEL default value of the main report to the police, the system automatically stops the control operation, "cabinet superscalar "light blinking, buzzer sound, press the mute button, the buzzer to stop ringing, the screen shows" superscalar inside. " Combustible gas concentration inside until the readings dropped to normal, after troubleshooting inside, press the "reset inside superscalar" button "inside superscalar / reset" indicator goes out, the system can be re-run of the detection of accommodation for Sampling and Monitoring. 6. Failure to deal with 6.1 false alarm 6.1.1 to carry out artificial Purge pipeline, scheduled to make the residual gas sampling tube, the re-sampling measurement. 6.1.2 display alarm settings to check whether it is normal, if not correct, re-setting. 6.1.3 using a standard calibration gas sensors, if there is deviation, re-zero, gain calibration. 6.1.4 Inspection PLC working condition. 6.2 does not alarm 6.2.1 display alarm settings to check whether it is normal, if not correct, re-setting. 6.2.2 using a standard calibration gas sensors, if there is deviation, re-zero, gain calibration. 6.2.3 Inspection PLC working condition. 6.3 sampling pump does not work 6.3.1 sampling pump power to check whether it is normal for loop. 6.3.2 check whether it is normal for sampling pump. 6.3.3 inspection system for locking the state of alarm inside and if so, to reset. 6.3.4 inspection system is in purge mode. 6.4 system can not automatically switch sampling loop 6.4.1 inspection system in the automatic mode to choose whether or not a state. 6.4.2 Inspection PLC working condition.