爱吃糖z
2.1. Connect the power supply. Connect the charger to the power, indicator light flashing on 0.5 seconds (0.5 seconds), said the charger for standby mode now.2.2. Connecting the battery. Connect the charger and battery. The charger the red clip to the positive (+) battery, black clip connect the cathode (-).2.3. The charging step 1 - go to sulfide. After connecting battery indicator Chang Liang at this time, LCD backlight lights, LCD display the charging step 1, analyzes the degree of cure of battery charger, if need to sulfide, the sulfide operation output pulse current. When the degree of cure battery or 8 hours time to return to normal in step 2. If the battery degree of cure is not obvious, go directly to step 2.2.4. The charging step 2 - quick charge. The lamp Chang Liang, LCD backlight lights, LCD display the charging step 2, the charger full power output, when the battery voltage to 13.5 V 8 hours or time to time, in step 3.2.5. The charging step 3 - filling. The lamp Chang Liang, LCD backlight lights, LCD display the charging step 3, diminishing the charger output current, if the battery voltage to 14 v or 10 hours time to time, in step 4. 2.6. The charging step 4 - analysis. The lamp Chang Liang, LCD backlight lights, LCD display the charging step 4, the charger output shut down, after 3 minutes, if the battery voltage in 12 v above, in step 5. If the voltage drop below 12 v, LCD display the charging step 4 flashing, buzzer sounded at the same time, the battery may need to change. 2.7. The charging step 5 - compensation charge. The lamp Chang Liang, LCD backlight lights, LCD display the charging step 5, charger shut down output, after 10 days, if the battery voltage drops to 10 v, charging cycle starts again. In more than 10 v, if the battery voltage to compensate the battery charger is charging, during this period, when the battery voltage to 13 v, in step 6.2.8. The charging step 6 - pulse charge. The lamp Chang Liang, LCD backlight lights, LCD display the charging step 6, the charger output pulse current, to keep the battery voltage at the highest. 2.9 out of charge. If the charger with the battery disconnected during the charge cycle, the charger automatically return to standby mode, close the output at the same time.
黑暗中的精灵88
power是电源灯DSL是电话线是否连接号的信号灯（DSL，数字用户专线）Internet是拨号上网成功后的信号灯Ethernet是猫与电脑连接成功后的信号灯闪表示正在传输数据！除了internet灯不亮，其他都是正常的，Internet灯不亮是因为你没拨号上网或者没有使用网络！
皖北一只老色
Pwr灯：电源指示灯(常亮：电源输入正常；常灭：无电源输入或输入不正常）Act灯：数据指示灯(闪烁：表示有数据传输。常灭：无数据传输）Alarm灯：错误指示灯(常亮：ADSL数据传输有错误；常灭:ADSL数据传输正常）ADSL灯：连接状态指示灯(常亮：表示已连接电信局端。常灭：端口表示没有连接上。闪烁：端口正常传输数据）LAN灯：Ethernet指示灯。（常亮：LAN端口连接正常；常灭：LAN端口连接不正常；闪烁：LAN端口有数据传输）DSL不对吧,是ADSL吧. 猫不影响啊,用的分频器把猫和电话都是分开的.一般是不会有这样情况的啊.不会吧,占线.....
Tracy猪猪
2.1. to connect the power supply. Connect the charger to the power supply, flashing lights (0.5 seconds on destroyed in 0.5 seconds), said charger now as standby. 2.2. connect battery. The charger is connected with the battery. Chargerred clip connected battery positive (+), black clip isconnected with the cathode (-). 2.3. charging step 1-- tosulfide. After the battery is connected, the indicator light,LCD backlight brightness, the LCD display charging step 1,curing degree of the battery charger is analyzed, if need tocure, the output pulse current to curing operation. When the curing degree of the battery recovery to normal or 8 hours of regular time, go to step 2. If the batteryvulcanization degree was not obvious, go directly to step 2.2.4. charging step 2-- fast charging. The indicator light,LCD backlight brightness, the LCD display charging step 2,chargers full power output, when the voltage of the batteryto 13.5V or 8 hours from time to time, go to step 3. 2.5. charging step 3-- flat charge. The indicator light, LCDbacklight brightness, the LCD display charging step 3,decreasing the charger output current, if the batteryvoltage to 14V or 10 hours from time to time, go to step 4.2.6. charging step for 4-- analysis. The indicator light, LCDbacklight brightness, the LCD display charging step 4, the charger output closed, after 3 minutes, if the battery voltage is maintained at more than 12V, go to step 5. If the voltage drops below 12V, charging step LCD display 4 flashes at the same time, buzzer, suggesting that the current battery may need to be replaced. 2.7. chargingstep 5-- charging compensation. The indicator light, LCD backlight lights, LCD display charging step 5, the chargerturns off the output, 10 days later, if the battery voltagedrops to 10V, the charge cycle begins again. If the battery voltage is above 10V, the charger for battery charging compensation, during this period, when the battery voltageto 13V, go to step 6. 2.8. charging step 6-- pulse charging.The indicator light, LCD backlight lights, LCD displaycharging step 6, the charger output pulse current, the battery voltage is maintained at the highest. 2.9. exit from the charge. If the charger and battery during the charge cycle disconnected, the charger automatically return to thestandby state, and closes the output.
